IS 2062 STANDARD 2006 PDF
Wrought Steel Products Sectional Committee, MTD 4 FOREWORD This Indian Standard (Sixth Revision) IS Indian Standard HOT. education and knowledge, the attached public safety standard is made in and revised in , , , , and 15 BIS BUREAU OF INDIAN STANDARDS. MANAK BHAVAN, 9 this standard, in the light of experience gained during these years, the.
|Language:||English, Spanish, Indonesian|
|ePub File Size:||25.54 MB|
|PDF File Size:||17.69 MB|
|Distribution:||Free* [*Regsitration Required]|
IS - Free download as PDF File .pdf), Text File .txt) or read online for free. i) The title of the standard has been changed to `Hot Rolled Structural. IS Indian Standard. HOT ROLLED MEDIUM AND HIGH TENSILE. STRUCTURAL STEEL-SPECIFICATION. (Seventh Revision). 1 SCOPE. IS - HOT ROLLED LOW, MEDIUM & HIGH TENSILE . The Indian standard specification tolerances on shape, dimensions and mass of structural.
The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard. MTD 4 1. At the time of publication.
All standards are subject to revision and parties to agreement based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below: IS No.
Part 1 Carbon and low alloy steels second revision Title Method for chemical analysis of steel in various parts If required. The finished material shall be reasonably free from surface flaws. Reduction in thickness by grinding greater than 4 percent but not exceeding 7 percent may be made subject to mutual agreement between the purchaser and the manufacturer.
MTD 4 both their local properties and their influence on the construction of which they form a part.
Max 1 2 Carbon 0. MTD 4 7.
For testing of flat products like plates tensile and bend test pieces may be cut in the transverse direction. Selection of location of test pieces may also be mutually agreed between the purchaser and the manufacturer.
The recommended locations for taking test samples for plates. In case of dispute. Permissible limits of variation in case of product analysis from the limits specified in Table 1 shall be as given in Table 2. In case of plates the number of plates in each cast shall also be given. Round test samples are permitted. In case of bars having diameters or thickness between 28 mm and 71 mm.
In case of plates. If shearing of flame-cutting is employed. At least one rolled surface shall be left on rectangular test samples taken from plates exceeding 32 mm in thickness. MTD 4 9.
Any slight straightening of test samples which may be required shall be done cold. If this is not possible. The rolled surface of the test piece shall be on the outer side of the bend during the test.
For bars having diameters or thicknesses exceeding 71 mm. MTD 4 The tensile strength. One additional test shall be made for each class of product and for each variation of thickness.
When section permits. If the manufacturer so desires. The test shall be carried out as on the standard test pieces prepared in accordance with IS The number of tests for every 50 tonnes of material or part thereof.
If the test sample taken from the thickest product rolled from a cast meets the requirements. Provided this new average complies with the specified requirement.
IS 2062 -2006 (2)
The notch axis shall be perpendicular to the rolled surface. Temperature of charpy impact test will be subject to mutual agreement. If the average value of the three charpy impact tests fails to comply by an amount not exceeding 15 percent of the specified minimum average value. If this thickness also does not meet the requirements.
For Comments Only
MTD 4 The test specimen is parallel to the direction of rolling and the base closer to the rolled surface is more than 1 mm from it. NOTE — The Y groove crackability test will not be applicable for rounds and it is mainly for plates and sections. Stricter tolerances may be followed.
Channel and angle IS Currently available Indian Standard are listed in Table 4. Should the test pieces from either of these additional samples fail.
Should the test pieces from both these additional samples pass. Part 2: Part 2 Sections TS H.
Most Recent Superseded COM ; Nov 1, Ltd, Sponge Iron ; Nov 1, In its second revision of , the title of the standard was modified to ' Specification for cold-worked steel high strength deformed bars Bureau of Indian Standards is the subject of the November Gov ; Sep 18, In view of the above, I respectfully submit that the Indian Standards be made freely Forethought had been founded in to create an integrated environment and applications for future personal computers that would provide a graphical user interface, but it had run into difficulties requiring a "restart" and Generator Protection System.
BEg Protection Device pdf manual download.When section permits, these shall be not less The possible information regarding properties in the cross- finished material shaIl be reasonably free from surface sectional and longitudinal planes. At the time of publication. Are you sure you want to Yes No. Provided this new average complies with the specified requirement, the material represented shall be deemed to comply with this standard.
IS 2062 E350 Steel Manufacturer in India
For Applicants: 1. When section permits. Should the test pieces from either of these additional samples fail, the material represented by the test samples shall be considered as not having complied with this standard.
- EMBEDDED C CODING STANDARD BY MICHAEL BARR PDF
- ACCOUNTING STANDARDS ISSUED BY ICAI PDF
- THE STANDARD BOOK OF SPELLS GRADE 1
- STANDARD FOR PROGRAM MANAGEMENT 3RD EDITION PDF
- 11TH STANDARD CHEMISTRY BOOK
- THE STANDARDS REAL BOOK BB
- STANDARD METHODS FOR THE EXAMINATION OF WATER AND WASTEWATER BOOK
- INTERNATIONAL FINANCIAL REPORTING STANDARDS EBOOK
- COGNITIVE COMPUTING AND BIG DATA ANALYTICS PDF
- ED MCBAIN PDF
- INTERNATIONAL FINANCIAL REPORTING STANDARDS EBOOK
- WARIS SHAH HEER IN PUNJABI PDF
- WORLD LINK INTRO PDF
- THEORY OF FLIGHT BOOK